MINIMOTO Universal Holder-A very good tool for locking the bell of the front or rear scooter variator when unscrewing nuts in a garage environment.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
MINIMOTO Universal Holder-A very good tool for locking the bell of the front or rear scooter variator when unscrewing nuts in a garage environment.
This tool does what you want if you use it for its intended purpose. I bought the Husqvarna flywheel to hold while tightening the nut. Some said it failed and didn't do its job. Don't use it to change the oil filters in your car or load your ex-girlfriend's tire and it should work just fine.The safest non-destructive way to hold the flywheel for removal of the highly torqued nut. Could use a stronger clamping shaft to hold things while re-torquing the nut during installation. Bends a little too easily. Also, the vinyl coating on the band is slippery on a smooth flywheel surface. Powdered resin solves the slip issue.I've used this on a few motorcycles, Honda and Husky and it still looks and works as it should. I recommend it.View Detail
Приобрел данное приспособление для стопорения шкивов скутера (максискутера) при откручивании гаек на осях вариатора и торкдрайвера.Покупкой доволен!Очень полезный инструмент для замены ремня вариатора.I purchased this device for locking the pulleys of a scooter (maxiskuter) when unscrewing the nuts on the axles of the variator and the torc driver. Satisfied with the purchase! A very useful tool for replacing the variator belt.translated by Google TranslatorView Detail
[How is it used?
Used to remove Clutch and Pulley from Scooter
Was the one you received as per Image?
No problem as per Image.
How was your experience with it?
I have not had any inconvenience at all.
[Points to note]
The holes are positioned in the most comfortable manner (opening angle), and then tightened and secured in place.
How did it compare to other products?
The product is not different in usability compared to the well-known manufacturer's product used in the past, and this product can be recommended because it is less expensive.View Detail
I bought this for maintenance of my scooter's drivetrain.
Until I purchased the Impact wrench, I had to hold the clutch outer with this product and remove it with the Ratchet wrench.
The plug-in type universal holder was difficult to use with the Clutch outer tightening torque, so I needed two types.
The price is very Reasonable and it is very easy to use.
I've been using it for about two years and it hasn't broken yet.
Now that I have purchased an electric impact wrench, I have less opportunity to use it on the drive train, but instead I use it around the crank and when removing the generator.
I feel that there are many opportunities to use it not only for Motorcycle, but also for cars.
Since it is variable and can be used for a variety of sizes, I think having one for now will come in handy later.
It is flat when placed on the ground, so it can be placed in the crevices of shelves, and I keep it hanging on the wall so it does not take up much space.
Sometimes when the lid of a bottle is too hard to open, I use this product, and it opens in one shot. However, be careful not to tighten it too much or it will break.View Detail
I purchased this product to replace the Reinforced Clutch and Reinforced Oil Pump on my SUPER CUB 50FI.
I was able to hold it firmly without any slippage.
It's cheap and large, and I'm happy with it.View Detail
On the 2001 Honda Forza MF 06, after 15,000 km, the suspension bearing of the right rear wheel hummed. Replaced with NTN products. After that I drove 3000 km, I'm happy with the result. When pressing in the bearing, so that the seat does not wobble, you first need to heat the suspension part with an industrial hair dryer to a temperature of 150 degrees C. This product has a metal protection for the balls, bearings with a plastic ring are installed on the scooter at the factory.View Detail
Fits: YAMAHA TT-R110E 08- [Number of genuine links]90, YAMAHA RZ50 81-89 [Number of genuine links]106, YAMAHA RX80 81 [Number of genuine links]110, YAMAHA RX50 80-81 [Number of genuine links]110, YAMAHA RD50 81-87 [Number of genuine links]112
This chain is used on a Honda MTX 50 and is used in tough off-road conditions. In the mountains, in swampy areas, when overcoming water obstacles up to 0.5-0.6 m deep, the DID STD Series Chain 420D Steel shows itself only positively. It retains its size (does not stretch) when used in enduro conditions no less than for 1000 km.At the same time, it works constantly in mud and with a lack of lubrication.View Detail
After 10 years of operation of the maxiscurator, the grease dried up in the drain bearings and they became unusable. A play appeared on the wheel. I replaced them with Koyo bearings. I need to remove old ones and put new bearings on the wheel’s hot disk, it must be heated with an electric hairdryer. After replacing the bearings Koyo passed 5000 km without any problems.View Detail
On my Honda NSS 250 mf 06 maxiskooter, when the steering wheel was turned too hard, the windshield was touched by the risk of breaking it off. I installed the Ai-net Mirror Adapter (10 mm thread, 1.25 pitch) to the right and left. As a result, the mirrors began to be above the fairing . Adapters are made of high quality, most likely stainless steel. They look good, the exterior of the scooter does not break.View Detail
Fits: SUZUKI RANDY(FM50) *Required number:1, SUZUKI JR50 78 *Number of units required:1, SUZUKI K125 80-94 *Number of pcs required:1, SUZUKI K90 67-91 *Number of pcs required:1, SUZUKI K125 95 *Number of units required:1
Iridium candle was installed on a 2-stroke air cooling Suzuki K 125 motorcycle. The engine on it starts confidently, works well both at medium (3500-4500) and at high speeds (7000-8000). There are no spark plugs in the ignition. The engine pulls well.The carburetor adjusted to a normal mixture, not poor and not rich, brown soot, the motor does not overheat.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Εξυπηρέτηση πελατών
ΠΑΡΑΓΓΕΛΙΕΣ
ΠΛΗΡΟΦΟΡΙΕΣ
ΣΧΕΤΙΚΑ ΜΕ ΕΜΑΣ
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING