* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I bought it to eliminate the weight of SRX Clutch. I think that the weight of SRX's Clutch has the following three causes.
1 : Wire's Access to Clutch release forced to bypass with Type 4 retrofitted Engine Starter Motor. 2 : Small Small Front Slightly hard fitting around the circumference of Wire. 3 : Clutch lever & Holder crooked in the middle of design priority and straight without going into force on Holder.
In response to the above problems, this product solves the first problem. As a structure, use this principle (Extension of Wire holder of Clutch release side) It will surely be lighter. However, due to its structure, there seems to be a problem that Clutch's meeting position changes on the Clutch lever side, or the depth of the semi-Clutch changes, but I am a Pro taper made Clutch holder & Lever (PROFILE Clutch Perch) To make it possible to operate without any inferiority to OEM.
As for assembly, I was able to assemble using several kinds of Hex without removing Engine Starter Motor. How many minutes it was difficult to install the Engine Starter Motor as it was installed in the way. I think that it can be mounted very easily once the Engine Starter Motor is removed.
150 Km in use during installation Its own Clutch lever operation, the middle finger - Quantity of ring finger : Although it was done with 2 pc, the movable width increased Clutch could not run out, I reduced the play of Wire, but I am not satisfied yet. Try changing the Lever operation, changing the play of Wire, now being adjusted To lighter the original purpose, if Clutch can not run out to the extent that it feels a little lighter I am thinking about removing it. Installation was removed by removing carburetor, Engine Starter Motor, but personally it is troublesome I did not feel it, I worked very well with expectation after installation.View Detail
If you remove the CellMotor it will be easier to install. Engine Starter Motor can be removed without removing carburetor. Remove Screw, hit it from the other side, turn it to Left and remove it.
There seems to be individual differences depending on the body, so it may be necessary to adjust.
I was not that much, but it seems that Cover and Limit of Air cleaner box will interfere - - - But it is about OK..
Clutch will certainly be lighter, but the necessary Stroke will increase. As moving parts also increases, I feel like reducing the feeling of rigidity?.
At the same time it would be better to change the handling of Clutch Cable.View Detail
Clutch 's weight itself was acceptable because it runs only a long distance, but it was hard to get Neutral' s entry difficulty, so I installed it at the opportunity of carburetor and Engine Starter MotorOH Although there are new types using negative pressure from NAG, we do not do Race, so we bought this cheap one Although the Instruction Manual on the other person is simple, the principle was simple enough, but depending on the state of the installation side it was better to shave Arm 's Crimp as well as cut my own case In the state where it was loaded in Frame, I was troubled with scraping and I sent it off You can also say that Bolt and Spacer instead of Crimp are included The feeling of use of the product is satisfied, although it is a simple structure Aluminum Cut - out It was a good bargain if Clutch got lighter with proper accuracy (* ` - Ω - AsuView Detail
150 Km in use during installation Its own Clutch lever operation, the middle finger - Quantity of ring finger : Although it was done with 2 pc, the movable width increased Clutch could not run out, I reduced the play of Wire, but I am not satisfied yet. Try changing the Lever operation, changing the play of Wire, now being adjusted To lighter the original purpose, if Clutch can not run out to the extent that it feels a little lighter I am thinking about removing it. Installation was removed by removing carburetor, Engine Starter Motor, but personally it is troublesome I did not feel it, I worked very well with expectation after installation.View Detail
If you remove the CellMotor it will be easier to install. Engine Starter Motor can be removed without removing carburetor. Remove Screw, hit it from the other side, turn it to Left and remove it.
There seems to be individual differences depending on the body, so it may be necessary to adjust.
I was not that much, but it seems that Cover and Limit of Air cleaner box will interfere - - - But it is about OK..
Clutch will certainly be lighter, but the necessary Stroke will increase. As moving parts also increases, I feel like reducing the feeling of rigidity?.
At the same time it would be better to change the handling of Clutch Cable.View Detail
Clutch 's weight itself was acceptable because it runs only a long distance, but it was hard to get Neutral' s entry difficulty, so I installed it at the opportunity of carburetor and Engine Starter MotorOH Although there are new types using negative pressure from NAG, we do not do Race, so we bought this cheap one Although the Instruction Manual on the other person is simple, the principle was simple enough, but depending on the state of the installation side it was better to shave Arm 's Crimp as well as cut my own case In the state where it was loaded in Frame, I was troubled with scraping and I sent it off You can also say that Bolt and Spacer instead of Crimp are included The feeling of use of the product is satisfied, although it is a simple structure Aluminum Cut - out It was a good bargain if Clutch got lighter with proper accuracy (* ` - Ω - AsuView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING